Bezel with flowers from foiramane
On the rim, small flowers are located on one half, made of plastic suede without special tools.
To work on the decoration we take materials:- bezel. - acrylic paints. - scissors. - wire. - plastic suede pink and green. - thin satin ribbon. - sponge or foam rubber . - pencil with a fixed eraser. - curling hair. - plastic sheet for from printing textures. - stamens for flowers. - toothpick. - lighter. - thin green paper. - Moment glue is transparent. The composition will have 11 flowers, each with 2 rows of petals. Therefore, from pink suede, you need to cut 22 squares with a side of 4 cm. And from the green material you will need 8 rectangles 5 x 3 cm.
Now on these bases we will make petal circles and leaves.
From green details we make the shape of a leaf. And from the pink parts, first cut a circle, rounding the corners. Then, arbitrarily, from the center, divide it into 5 petals, and cut out only by upper roundings. Then we cut the edge of each petal towards the center, leaving a middle 1.5 cm in diameter, whole.
Now turn to staining. We take acrylic paint of yellow and red color and apply a piece of foam rubber on the edges of the flap circles on both sides.
A yellow center should be applied only from one side.
Leave the petals to dry completely and proceed to the leaves. First, they need to make the veins. In the first way, you can simply draw a toothpick on the sheet itself. In the second method, a plastic sheet with a convex structure can be used.But for this, the leaf itself should be slightly warmed up by attaching it to the hair curler.
And at once we apply a warm template on the texture, well pressing his.
The leaves should have a clear imprint of veins.
Now these pieces should be slightly colored in red only on the edge from two sides.
But processing is not completed. Next you need to trim the shape of the sheet with scissors so that the main vein is in the middle of the workpiece. Then we make small cloves around the edge. Now fold the sheet in half and fold, touch the warm curling for a few seconds, and then press it with your fingers, an interesting fold is obtained.
Bye leaves set aside.We return to the flowers. Additionally, you need a pencil with an eraser and a sponge. You need to give the petals a new shape. We heat the circle on the curling iron, position it on the sponge and press the middle of the petal circle deep into the foam rubber.
We get a blank in the shape of a cup. It should be noted that the yellow part must remain inside.
Process all petals with such movements.
But the beauty of the circles lies in a different treatment. Now it is necessary to process each petal of the flower circle separately with a cigarette lighter. On the small part we make two folds. We heat with a lighter and, while the suede is warm, with our fingers we form a bend. This will have to be done from two sides.
We process all 5 parts of the petal circle.
This shape allows the flower to be lush.
Now go to the stamens. On one flower we use a pair of double blanks. Cut into 11 pieces of wire 5 cm long. At one edge of the segment we apply stamens folded in half, 1 cm above the wire. And we fix a little by winding the thread.
When the stamens are ready, you should immediately paste the whole wire into strips of thin green paper.
Go to dried leaves. For them, too, should be prepared pieces of wire 6 cm long. Then we fasten the sheet onto the wire, piercing several times the bottom of the sheet.
Then you need to smear the sheet and wire on the front side with a glue and good press on the fold. Now we take the petal circles and fold in pairs, two together, we glue together a little in the center.Then we pierce in the middle with a toothpick, making a hole.
And then we put the stamens in there and taped the connections again.
On the finished colors you need to make the bends of the wire. Retreat 1.5 cm from the workpiece and on green stems do bend at 90 degrees. And go to the assembly on the bezel.
We start winding with a thin tape from one edge of the bezel, smearing it with glue in small gaps. Passing the tape 10 cm from the edge, we attach the sheet, tilting it with a corner to the bottom of the rim, and make several turns with a ribbon on the stalk.
Next we place the flower, the bent part on the bezel and also fix it with a ribbon.
The following flowers are arranged in a checkerboard pattern and rim .Then put the leaf. Then arrange all the flowers and leaves one by one. And turn the last flower with a leaf to the middle of the rim.
It remains only to glue the tape for the rest of the bezel. And the decoration is ready. Thanks to the wire, flowers can be corrected at your discretion.
Good luck to all!
A tiffany-colored folding greeting cardOriental Bonsai Wire and Yarn WoodA brooch made of satin and satin ribbonsDelicious recipes - cook with loveBouquet of roses from feltFiller Chicken MedusaFloor covering